Arcosa Pottery Plaster
Our newest pottery plaster.
Documents
If you make molds, you've probably heard: US Gypsum (USG) has stopped making No. 1 Pottery Plaster. For decades, No. 1 was the standard plaster for slip-casting molds in the US. This summer, USG closed its plant in Southard, Oklahoma, which made No. 1 along with Hydrocal, Hydro-Stone, Ultracal, and its other specialty plasters.
Meet Our New Pottery Plaster: Arcosa
It's official! We now carry Arcosa Pottery Plaster, made by Arcosa Specialty Materials in Oklahoma.
Arcosa was recommended to us by US Gypsum itself! It is the most comparable plaster on the market, so we are excited to bring it to Seattle Pottery Supply.
Will It Be Different?
The honest answer: on paper, it's very close! Only casting in it will tell you for sure.
Here are some comparisons:
USG No. 1 |
Arcosa Pottery Plaster |
|
|---|---|---|
Water per 100 parts plaster (by weight) |
70 |
67–70 |
Dry compressive strength |
2,400 psi |
2,500 psi |
Maximum setting expansion |
0.21% |
0.3% |
Sources: USG No. 1 data sheet and safety data sheet (SDS); Arcosa Pottery Plaster data sheet and safety data sheet (SDS).
- Same mix. If you mix No. 1 at 70 parts water to 100 parts plaster, mix Arcosa the same way.
- Same strength, within normal variation.
- A little more expansion as it sets. You won't notice it in a bat or a one-piece mold. It can matter in a multi-part mold whose pieces have to register tightly.
- Absorption isn't on either data sheet. This will impact how fast a mold casts and how many times you can cast with it.
Arcosa's Test of Our New Batch
Arcosa tests every lot before it ships. Here are the results from our first truckload:
Lot 101426, tested October 15, 2026; download the certificate.
|
|
Acceptable Range: Set by Arcosa. |
Our Lot |
|---|---|---|
Set time, hand mixed |
17–26 minutes |
23 minutes |
Water needed to reach a standard pouring thickness, per 100 parts plaster |
62–65 |
65 |
Fineness (passes a 100-mesh screen) |
over 98.5% |
99.6% |
- Set time: 23 minutes, hand mixed. USG listed No. 1 at 14–24 minutes when mixed by machine and noted that hand mixing takes longer, so expect a similar working time. Water temperature and mix time change the set time more than the brand does.
- Arcosa's data sheet says it needs a little less water than No. 1 to flow. In our shop, at 70 parts water, it actually felt a little thicker than No. 1 during mixing and pouring. Less water makes a harder, denser mold that absorbs a little more slowly; more water does the reverse.
Wedging Boards and Plaster Bats: Our First Pour with Arcosa

We make our plaster wedging boards and bats in-house with a blend of pottery plaster and hydro-cal plaster for improved strength. After receiving our shipment of Arcosa, we cast a set of boards and bats to compare to our old No. 1 plaster blend. The Arcosa plaster was mixed with hydro-cal in the same ratio as our original blend.
What We Noticed:
Color
- Arcosa is slightly warmer in color than No. 1. You can see it well when they're side by side. On its own, it still looks very white.
Smell
- We noticed a slightly stronger, more distinct odor when the Arcosa pieces came out of the mold.
Mixing
- Arcosa felt a little thicker during the mixing stage, even with the same water-to-plaster ratio.
Set Time
- No difference! Both came out of the molds in about 30 minutes.
Our Side-by-Side Slip-Cast Test:
The question we hear most from mold makers is simple: will a mold made with Arcosa cast like one made with No. 1? Data sheets can only give us so much information, so we're finding out in our own shop!
Step 1: Make two identical molds
We made two 2-piece molds from the same small pitcher—one in USG No. 1 and one in Arcosa.
Same master, same method, and the same mix for both: 70 parts water to 100 parts plaster, by weight.
Here is our method:
2. First half of mold poured and set.



5. Second half poured and set.


Completed Molds:


Step 2: Slip-Cast Comparison
We'll slip-cast a form from each mold using the same batch of slip. These will be cast at the same time to account for environmental conditions. After 20 minutes, the molds will be turned, allowing the slip to drain from them. We will unmold after 24 hours from pour time.
The following will be recorded:
- Wall thickness.
- Ease of release.
- Any surface imperfections or texture.

Making the Switch as a Home Potter
We know this is a big transition! Here are some ways you can keep your process consistent, even with a new plaster:
Try making a test mold before you remake anything important.
- For a limited time, we're selling 1 lb bags! We encourage you to buy one and make a test mold before committing to a full 25- 50 lb bag.
Keep your mixing routine the same.
- Weigh the water and the plaster, sift the plaster in, soak 2–4 minutes, then mix. Our plaster mixing instructions still apply.
Cast with your own slip from the test mold.
- Using your favorite slip, compare wall thickness, dry time, and ease of release against one of your existing No. 1 molds.
Don't combine plasters within one mold set.
- Pour every piece of a multi-part mold from the same plaster so the pieces fit and absorb evenly. Molds you already own will keep working.
What about Hydrocal and Hydro-Stone?
Arcosa doesn't make a replacement we can buy for these USG gypsum cements. We have limited stock of both, and a purchase limit in place.
We're still looking for a supplier and will update this post when we find one!
A note while we're here: Hydrocal and Hydro-Stone are not substitutes for pottery plaster in slip-casting molds. They're much harder and absorb very little water. These plasters are ideal for sculpture and master patterns.
Still have Questions?
Call us at 888-915-1196 or stop by our Seattle storefront!